Lantech IPGS-5008T (IP67/IP54) is a high performance L2+ All Gigabit Ethernet switch with 8 10/100/1000T w/8 PoE at/af injectors up to 30W@ at M12 X-coded providing L2 wire speed and advanced security function for network aggregation deployment. It houses in a IP67/IP54 aluminum compact enclosure that is waterproof and will prevent moisture ingress due to temperature fluctuations. It delivers ITU G.8032 enhanced ring recovery less than 20ms in single ring while also supports train ring, enhanced mode, multiple VLAN mode with easy configuration. The comprehensive QoS, QoS by VLAN, advanced security including INGRESS/EGRESS ACL L2/L3, TACACS+, SSH/SSL, Mac based DHCP server, DHCP Option 82, DHCP server, IGMPv1/v2/v3/router port, QinQ are supported and also required in large network. It also supports10K Jumbo frame.
Selection of dual WV (16.8V~137.5VDC) input and 24V (12~56VDC), High PoE budget
WV model w/system isolation accepts 16.8~137.5VDC dual input and can feed 54V output with max 120W PoE budget. WVI w/PoE isolation and can feed max 80W PoE budget. 24V model w/system isolation accept 12~56VDC dual input for PoE feeding with max 120W budget.
PoE +, Advanced PoE management
Lantech IPGS-5008T (IP67/IP54) supports IEEE802.3at/af standard which can feed power up to 30W at each PoE port for big power consumption devices like PTZ IP camera, wireless AP etc. The advanced PoE management includes PoE detection and scheduling besides the regular PoE per port status. PoE detection can detect if the connected PD is hang up then restart the PD; PoE scheduling is to allow pre-set power feeding schedule upon routine time table. Per port PoE status can remotely On/Off the power and display information of voltage, current, watt and PoE temperature.
Enhanced G.8032 ring, 16 MSTI MSTP; Optional MRP ring
Lantech IPGS-5008T (IP67/IP54) features enhanced G.8032 ring which can be self-healed in less than 20ms for single ring topology protection covering Multicast packets. It also supports various ring topologies that covers double ring, multi-chain (under enhanced ring), train ring, basic ring, multiple-VLAN ring and auto-ring by easy setup than others. The innovative auto-Ring configurator (auto mode) can calculate owner and neighbor in one step. It supports MSTP that allows RSTP over VLAN for redundant links with 16 MSTI. Optional MRP (Media Redundancy Protocol) can be supported for industrial automation networks.
Re-powered ring restoration, Miss-wiring alert, Loop protection
The IPGS-5008T (IP67/IP54) also embedded several features for stronger and reliable network protection in an easy and intuitive way. When the pre-set ring configuration failed or looped by miss-wiring, Lantech IPGS-5008T (IP67/IP54) is able to alert with the LED indicator and disable ring automatically. Repowered auto ring restore function (node failure protection) ensures the switches in a ring to survive after power breakout is back. The status can be shown in NMS when each switch is back. This feature prevents the broken ring and keep ring alive without any re-configuration needed. Loop protection is also available to prevent the generation of broadcast storm when a dumb switch is inserted in a closed loop connection.
QoS by VLAN for legacy device
QoS by VLAN can allow switch to tag QoS by VLAN regardless the devices acknowledge QoS or not in which greatly enhance the bandwidth management in a network.
QinQ, QoS QinQ* and GVRP supported
It supports the QinQ, QoS QinQ*, GVRP for large VLAN segmentation.
IGMPv3, GMRP, router port, static multicast forwarding and multicast Ring protection
The unique multicast protection under enhanced G.8032 ring can offer immediate self-recovery instead of waiting for IGMP table timeout. It also supports IGMPv3, GMRP, router port and static multicast forwarding binding by ports for video surveillance application.
DHCP option 82 & Port based, Mac based DHCP, Option66, IPv6 DHCP server**
DHCP server can assign dedicated IP address by MAC or by port (Port based for single switch) , it also can assign IP address by port for multiple switches with single DHCP option82 server. DHCP Option66 server can offer IP address of TFTP server to DHCP client for VOIP application. Optional IPv6 address resolution for DHCP service can be supported.
User friendly GUI, Auto topology drawing
The user friendly UI, innovative auto topology drawing and topology demo makes IPGS-5008T (IP67/IP54) much easier to get hands-on. The complete CLI enables professional engineer to configure setting by command line.
Editable configuration file
Optional N key auto backup, Exported text file
The configuration file of Lantech IPGS-5008T (IP67/IP54) can be exported in text file so that it can be edited and configured back to switch with ease for mass deployment. The optional N-key configurator offers firmware upgrade, auto backup/ editable configuration restore without computer by adjusting the DIP switch. The built-in watchdog design can automatically reboot the switch when CPU is found dead.
Event log & message; 4 DI + 3DO
In case of event, the IPGS-5008T (IP67/IP54) is able to send an email** & SMS** text message to pre-defined addresses as well as SNMP Traps out immediately. It provides 4DI and 3DO when disconnection of the specific port was detected; DO will activate the signal LED to alarm. DI can integrate the sensors for events and DO will trigger the alarm while sending alert information to IP network with email and traps.
Environmental monitoring for inside switch info
The built-in environmental monitoring can detect switch overall temperature, real input voltage, current and total PoE load where can send the SNMP traps, email** and SMS** alert when abnormal.
Relay alarm, High ESD protection
Featured with relay contact alarm function, the IPGS-5008T (IP67/IP54) is able to connect with alarm system in case of power failure or port disconnection events. The IPGS-5008T (IP67/IP54) also provides ±2000V EFT and ±6000V ESD protection, which can reduce unstable situation caused by power line and Ethernet.
EN50155, 45545-2, 50121-3-2, EN61373 verification
The IPGS-5008T (IP67/IP54) passed serious tests under extensive Industrial EMI and Safety standards. With EN45545-2 Fire & Smoke, and EN50155 verification, the IPGS-5008T (IP67/IP54) is best for railway in train/track side, vehicle and mining applications. For more usage flexibilities, IPGS-5008T (IP67/IP54) supports wide operating temperature from -40°C to 75°C.
Optional GigaT bypass
The optional bypass relay is set to bypass the switch to the next one when power is off in order to protect the network from crashing. Lantech bypass caters to remain in bypass mode until the switch is completely booting up when power is back to avoid another network lost. With optional bypass relay model, there will be 2 less PoE ports. (IP67 only)
|8361-4244||IPGS-5008T-67-WV||8 10/100/1000T X-coded EN50155 M12 IP67 L2+ PoE Managed Gigabit Ethernet Switch; 16.8~137.5VDC dual input; PoE max 120W budget; -40°C to 75°C|
|8361-4245||IPGS-5008T-54-WV||8 10/100/1000T X-coded EN50155 M12 IP54 L2+ PoE Managed Gigabit Ethernet Switch; 16.8~137.5VDC dual input; PoE max 120W budget; -40°C to 75°C|
|8361-4246||IPGS-5008T-67-WVI||8 10/100/1000T X-coded EN50155 M12 IP67 L2+ PoE Managed Gigabit Ethernet Switch; 16.8~137.5VDC dual input w/ PoE galvanic isolation; PoE max 120W budget; -40°C to 75°C|
|8361-4247||IPGS-5008T-54-WVI||8 10/100/1000T X-coded EN50155 M12 IP54 L2+ PoE Managed Gigabit Ethernet Switch; 16.8~137.5VDC dual input w/ PoE galvanic isolation; PoE max 80W budget; -40°C to 75°C|
|8361-4203||IPGS-5008T-67-24V||8 10/100/1000T X-coded EN50155 M12 IP67 L2+ PoE Managed Gigabit Ethernet Switch; 12~56VDC dual input; PoE max 120W budget; -40°C to 75°C|
|8361-4204||IPGS-5008T-54-24V||8 10/100/1000T X-coded EN50155 M12 IP54 L2+ PoE Managed Gigabit Ethernet Switch; 12~56VDC dual input; PoE max 120W budget; -40°C to 75°C|
|8850-100||N-key Configurator||RJ45 connector dongle for firmware upgrade, auto/editable configuration backup and restoration; -20°C to 60°|
|ECONM12-05A(M)-C-180||5 pin M12 (Male) A-coded 180 degree crimp type connector for Relay/Console|
|ECONM12-08A(M)-180||8 pin M12 (Male) A-coded 180 degree crimp type connector for DI/DO|
|ECONM12-08X(M)-SPEEDCON||8 pin M12 (Male) X-coded 180 degree crimp type connector for data, Ethernet CAT6A (10G), shielded, SPEEDCON|
|ECONM12-05A(F)-C-180||M12 5Pin (Female) A-coded 180 Degree Crimp Type Connector|
|ECONM12-5P(F)70CM CABLE||5 pin M12 power cable 90 degree angle, 70cm|
|ECONM12-5P(M)-W-180||M12 5P(Male) 180 Degree Wire Type Connector (DI/DO)|
|ECONM12-04D(M)-C-180||Connector,4-pin (Male),M12 D-coded Crimp Type 180 degree|
|ECONM12-05A(F)-C-180||M12 5Pin (Female) A-coded 180 Degree Crimp Type Connector|
|ECAB124030MJS||4 Pin M12 RJ45 Male 3 Meters; STP Cable|
|ECABM12X83MSTP||8 Pin M12 X-coded RJ45 Male 3 METER, STP CABLE w/ Shielding|