Lantech IPGS-5408DFT is a high performance L2+ (All Gigabit) industrial Ethernet switch with 8 10/100/1000T PoE at/af + 2 10/100/1000T + 2 Dual Speed SFP which provides L2 wire speed and advanced security function for network aggregation deployment. It delivers ITU G.8032 enhanced ring recovery less than 20ms in single ring while also supports train ring, enhanced mode, multiple VLAN mode with easy configuration. The comprehensive QoS, QoS by VLAN, advanced security including INGRESS/EGRESS ACL L2/L3, TACACS+*, SSH/SSL, Mac based DHCP server, DHCP Option 82, DHCP server, IGMPv1/v2/v3/router port, QinQ** are supported and also required in large network. It also supports Cisco Discovery Protocol (CDP) for Ciscoworks to detect the switch info and show on L2 map topology.
Up to 8 PoE at/af ports w/advanced PoE management
Compliant with 802.3af/at standard, the Lantech IPGS-5408DFT is able to feed each PoE port up to 30 Watt, total PoE budget 240W. Lantech IPGS-5408DFT supports advanced PoE management including PoE detection and scheduling. PoE detection can detect if the connected PD hangs then restart the PD; PoE scheduling is to allow pre-set power feeding schedule upon routine time table. Each PoE ports can be Enabled/disabled, get the voltage, current, Watt, and temperature info displayed on WebUI.
Miss-wiring avoidance, Repowered auto ring restore, Loop protection
The IPGS-5408DFT also embedded several features for stronger and reliable network protection in an easy and intuitive way. When the pre-set ring configuration failed or looped by miss-wiring, Lantech IPGS-5408DFT is able to alert with the LED indicator and disable ring automatically. Repowered auto ring restore function (node failure protection) ensures the switches in a ring to survive after power breakout is back. The status can be shown in NMS when each switch is back. Loop protection is also available to prevent the generation of broadcast storm when a dumb switch is inserted in a closed loop connection.
Enhanced G.8032 ring, 16 MSTI MSTP; Optional MRP ring
Lantech IPGS-5408DFT features enhanced G.8032 ring which can be self-healed in less than 20ms for single ring topology protection covering Multicast packets. It also supports various ring topologies that covers double ring, multi-chain (under enhanced ring), train ring, basic ring multiple-VLAN ring and auto-ring by easy setup than others. The innovative auto-Ring configurator (auto mode) can calculate owner and neighbor in one step.
Optional MRP (Media Redundancy Protocol) can be supported for industrial automation networks
DHCP option 82 & Port based, Mac based DHCP, Option66, IPv6 DHCP server**
DHCP server can assign dedicated IP address by MAC or by port (Port based for single switch) , it also can assign IP address by port for multiple switches with single DHCP option82 server. DHCP Option66 server can offer IP address of TFTP server to DHCP client for VOIP application. Optional IPv6 address resolution for DHCP service can be supported.
QoS by VLAN for legacy devices
QoS by VLAN can allow switch to tag QoS by VLAN regardless the devices acknowledge QoS or not in which greatly enhance the bandwidth management in a network.
QinQ**, QoS QinQ** and GVRP** supported
It supports the QinQ**, QoS QinQ**, GVRP** for large VLAN segmentation.
IGMPv3, GMRP**, router port, static multicast forwarding and multicast Ring protection
The unique multicast protection under enhanced G.8032 ring can offer immediate self-recovery instead of waiting for IGMP table timeout. It also supports IGMPv3, GMRP**, router port and static multicast forwarding binding by ports for video surveillance application.
User friendly GUI, Auto topology drawing
The user friendly UI, innovative auto topology drawing and topology demo makes IPGS-5408DFT much easier to get hands-on. The IPGS-5408DFT supports DMI interface that can correspond with DDM SFPs (Digital diagnostic monitor) to display the five parameters in Lantech’s UI, including optical output power, input power, temperature, laser bias current and transceiver supply voltage***. The TX power/RX power raw data is automatically converted to dB values for installer, making it easier to calculate the fiber distance. The complete CLI enables professional engineer to configure setting by command line.
Editable configuration file; Factory reset button
The configuration file of Lantech IPGS-5408DFT can be exported and edited with word processor for the other switches configuration with ease. The factory reset button can restore the setting back to factory default and built-in watchdog design can automatically reboot the switch when CPU is found dead.
USB port for configuration upload & download
The built-in USB port can have configuration upload & download by USB dongle.
Event log & message; 2 DI / 2DO
In case of event, the IPGS-5408DFT is able to send an email & SMS** text message to pre-defined addresses as well as SNMP Traps out immediately. It provides 2DI and 2DO when disconnection of the specific port was detected; DO will activate the signal LED to alarm. DI can integrate the sensors for events and DO will trigger the alarm while sending alert information to IP network with email and traps.
Optional environmental monitoring for switch inside information (-M model)
The optional environmental monitoring can detect switch overall temperature, voltage, total PoE load and current where can send the SNMP traps, email and SMS** alert when abnormal.
Wide range dual DC powered input; Relay contact alarm, High ESD protection
The Lantech IPGS-5408DFT is designed with wide range dual power input from ±44V~57VDC. Featured with relay contact alarm function, the IPGS-5408DFT is able to connect with alarm system in case of power failure or port disconnection. The IPGS-5408DFT also provides ±2000V EFT/SURGE and ±4000 VDC (Contact) / ±8000 VDC (Air) Ethernet ESD protection, which can reduce unstable situation caused by power line and Ethernet.
Industrial hardened design for extended temperature operation
Lantech IPGS-5408DFT features high reliability and robustness coping with extensive EMI/RFI phenomenon, environmental vibration and shocks usually found in factory, substation, steel automation, mining , process control and railway(EN50121-4). It is the best solution for Automation, transportation, surveillance, Wireless backhaul, Semi-conductor factory and assembly lines.
The -E model can be used in extreme environments with an operating temperature range of -40°C to 75°C
|8350-570||IPGS-5408DFT||2 10/100/1000T+2x100/1000 SFP + 8 10/100/1000T PoE at/af L2+ Industrial Managed Ethernet Switch w/USB slot & dual ±44 ~ 57VDC input; -20°C to 60°C|
|8350-571||IPGS-5408DFT-E||2 10/100/1000T+2x100/1000 SFP + 8 10/100/1000T PoE at/af L2+ Industrial Managed Ethernet Switch w/USB slot & dual ±44 ~ 57VDC input; -40°C to 75°C|
|8350-572||IPGS-5408DFT-M||2 10/100/1000T+2x100/1000 SFP + 8 10/100/1000T PoE at/af L2+ Industrial Managed Ethernet Switch w/USB slot & dual ±44 ~ 57VDC input; -20°C to 60°C Environmental monitoring|
|8350-573||IPGS-5408DFT-M-E||2 10/100/1000T+2x100/1000 SFP + 8 10/100/1000T PoE at/af L2+ Industrial Managed Ethernet Switch w/USB slot & dual ±44 ~ 57VDC input; -40°C to 75°C; Environmental monitoring|
|NDR-120 Series||120W Single Output Industrial Din Rail Power; 90-264VAC / 127-370VDC Input Range; Cooling by free air convection; RoHS2 ; Operating Temp. -20°C~70°C (ambient, derating each output at 2.5% per degree from 50°C ~ 70°C; For 115VAC, please refer to derating curve on NDR-120 Series datasheet)|
|Model name||Description||Model name||Description|
|8330-162-V1||MINI GBIC 1000SX (LC/0.5KM) Transceiver||8330-187-V1||LTSFP-1000BX-20KM Transceiver (WDM 1550)|
|8330-163-V1||MINI GBIC 1000SX2 (LC/2KM) Transceiver||8330-180-V1||LTSFP-1000BX-40KM Transceiver (WDM 1310)|
|8330-165-V1||MINI GBIC 1000LX (LC/10KM) Transceiver||8330-182-V1||LTSFP-1000BX-40KM Transceiver (WDM 1550)|
|8340-0591-V1||MINI GBIC 1000LHX (LC/40KM) Transceiver||8330-181-V1||LTSFP-1000BX-60KM Transceiver (WDM 1310)|
|8330-166-V1||MINI GBIC 1000XD (LC/50KM) Transceiver||8330-183-V1||LTSFP-1000BX-60KM Transceiver (WDM 1550)|
|8330-169-V1||MINI GBIC 1000XD (LC/60KM) Transceiver||8330-184-V1||LTSFP-1000BX-80KM Transceiver (WDM 1490)|
|8330-167-V1||MINI GBIC 1000ZX (LC/80KM) Transceiver||8330-185-V1||LTSFP-1000BX-80KM Transceiver (WDM 1550)|
|8330-170-V1||MINI GBIC 1000EZX (120KM) Transceiver||8330-071-V1||125Mbps BiDi SFP 2KM (WDM 1310) Transceiver|
|8330-168-V1||MINI GBIC 10/100/1000T (100m) Transceiver||8330-072-V1||125Mbps BiDi SFP 2KM (WDM 1550) Transceiver|
|8330-060-V1||100Base FX 2KM, Multi-mode, LC Transceiver||8330-069-V1||125Mbps BiDi SFP 20KM (WDM 1310) Transceiver|
|8330-065-V1||100Base FX 5KM, Multi-mode, LC Transceiver||8330-068-V1||125Mbps BiDi SFP 20KM (WDM 1550) Transceiver|
|8330-061-V1||100Base LX 30KM, Single-mode, LC Transceiver||8330-080||125Mbps BiDi SFP 40KM (WDM 1310) Transceiver|
|8330-197-V1||1.25Gbps BiDi SFP 0.5KM Transceiver (WDM 1310)||8330-082||125Mbps BiDi SFP 40KM (WDM 1550) Transceiver|
|8330-198-V1||1.25Gbps BiDi SFP 0.5KM Transceiver (WDM 1550)||8330-081||125Mbps BiDi SFP 60KM (WDM 1310) Transceiver|
|8330-195-V1||1.25Gbps BiDi SFP 2KM Transceiver (WDM 1310)||8330-083||125Mbps BiDi SFP 60KM (WDM 1550) Transceiver|
|8330-196-V1||1.25Gbps BiDi SFP 2KM Transceiver (WDM 1550)||8330-084||125Mbps BiDi SFP 80KM (WDM 1310) Transceiver|
|8330-188-V1||1.25Gbps BiDi SFP 10KM Transceiver (WDM 1310)||8330-085||125Mbps BiDi SFP 80KM (WDM 1550) Transceiver|
|8330-189-V1||1.25Gbps BiDi SFP 10KM Transceiver (WDM 1550)||8330-191-V1||Dual Speed SFP 100M/1000M-LX 10KM Transceiver|
|8330-186-V1||1.25Gbps BiDi SFP 20KM Transceiver (WDM 1310)||All SFP P/N# ended with D are with DDM function|
|MBAK19003||Wall mount bracket for 74(W) x 105 (D) x 152 (H) mm / 96 (W) x 105 (D) x 152 (H) mm Industrial switches|