Lantech IPGS-5408GSFP is a high performance L2+ (Gigabit uplink) switch with 8 10/100/1000T + 4 1000M SFP w/8 PoE 802.3af/at Injectors which provides L2 wire speed and advanced security function for network aggregation deployment. It delivers ITU G.8032 enhanced ring recovery less than 20ms in single ring while also supports train ring, enhanced mode , multiple VLAN mode with easy configuration. The comprehensive QoS, QoS by VLAN, advanced security including INGRESS/EGRESS ACL L2/L3, TACACS+*, SSH/SSL, Mac based DHCP server, DHCP Option 82, DHCP server, IGMPv1/v2/v3/router port, QinQ** are supported and also required in large network. It also supports Cisco Discovery Protocol (CDP) for Ciscoworks to detect the switch info and show on L2 map topology.
Up to 8 PoE at/af ports w/advanced PoE management
Compliant with 802.3af/at standard, the Lantech IPGS-5408GSFP is able to feed each PoE port up to 30 Watts@54 VDC providing the connected PD devices. Lantech IPGS-5408GSFP supports advanced PoE management including PoE detection and scheduling. PoE detection can detect if the connected PD hangs then restart the PD; PoE scheduling is to allow pre-set power feeding schedule upon routine time table. Each PoE ports can be Enabled/disabled, get the voltage, current, Watt, and temperature info displayed on WebUI.
Miss-wiring avoidance, Repowered auto ring restore, Loop protection
The IPGS-5408GSFP also embedded several features for stronger and reliable network protection in an easy and intuitive way. When the pre-set ring configuration failed or looped by miss-wiring, Lantech IPGS-5408GSFP is able to alert with the LED indicator and disable ring automatically. Repowered auto ring restore function (node failure protection) ensures the switches in a ring to survive after power breakout is back. The status can be shown in NMS when each switch is back. Loop protection is also available to prevent the generation of broadcast storm when a dumb switch is inserted in a closed loop connection.
DHCP option 82 & Port based, Mac based DHCP, Option66, IPv6 DHCP server**
DHCP server can assign dedicated IP address by MAC or by port (Port based for single switch) , it also can assign IP address by port for multiple switches with single DHCP option82 server. DHCP Option66 server can offer IP address of TFTP server to DHCP client for VOIP application. Optional IPv6 address resolution for DHCP service can be supported.
User friendly GUI, Auto topology drawing
The user friendly UI, innovative auto topology drawing and topology demo makes IPGS-5408GSFP much easier to get hands-on. The complete CLI enables professional engineer to configure setting by command line.
Enhanced G.8032 ring, 16 MSTI MSTP; Optional MRP ring
Lantech IPGS-5408GSFP features enhanced G.8032 ring which can be self-healed in less than 20ms for single ring topology protection covering Multicast packets. It also supports various ring topologies that covers double ring, multiple-VLAN ring and auto-ring by easy setup than others. The innovative auto-Ring configurator (auto mode) can calculate owner and neighbor in one step. It supports MSTP that allows each spanning tree for each VLAN for redundant links with 16 MSTI.
Optional MRP (Media Redundancy Protocol) can be supported for industrial automation networks.
Editable configuration file; USB port for configuration upload & download
The configuration file of Lantech IPGS-5408GSFP can be exported and edited with word processor for the other switches configuration with ease. The factory reset button can restore the setting back to factory default and built-in watchdog design can automatically reboot the switch when CPU is found dead.
The built-in USB port can have configuration upload & download by USB dongle.
QoS by VLAN for legacy device
QoS by VLAN can allow switch to tag QoS by VLAN regardless the devices acknowledge QoS or not in which greatly enhance the bandwidth management in a network.
QinQ**, QoS QinQ** and GVRP** supported
It supports the QinQ**, QoS QinQ**, GVRP** for large VLAN segmentation.
IGMPv3, GMRP**, router port, static multicast forwarding and multicast Ring protection
The unique multicast protection under enhanced G.8032 ring can offer immediate self-recovery instead of waiting for IGMP table timeout. It also supports IGMPv3, GMRP**, router port and static multicast forwarding binding by ports for video surveillance application.
Event log & message; 2 DI + 2DO
In case of event, the IPGS-5408GSFP is able to send an email & SMS text message to pre-defined addresses as well as SNMP Traps out immediately. It provides 2DI and 2DO when disconnection of the specific port was detected; DO will activate the signal LED to alarm. DI can integrate the sensors for events and DO will trigger the alarm while sending alert information to IP network with email and traps.
Optional environmental monitoring for switch inside information (-M model)
The optional environmental monitoring can detect switch overall temperature, voltage, total PoE load and current where can send the SNMP traps, email and SMS alert when abnormal.
Wide range dual DC powered input with galvanic isolation; Relay contact alarm, High ESD protection
The Lantech IPGS-5408GSFP is designed with dual power supply at 24/48VDC or single power supply at 90~305VAC/120~430VDC. Featured with relay contact alarm function, the IPGS-5408GSFP is able to connect with alarm system in case of power failure. The IPGS-5408GSFP also provides ±2000V EFT/SURGE and ±4000 VDC (Contact) / ±8000 VDC (Air) Ethernet ESD protection, which can reduce unstable situation caused by power line and Ethernet.
Industrial hardened design for extended temperature operation
Lantech IPGS-5408GSFP features high reliability and robustness coping with extensive EMI/RFI phenomenon, environmental vibration and shocks usually found in factory, substation, steel automation, aviation, mining and process control. It is the best solution for Automation, transportation, surveillance, Wireless backhaul, Semi-conductor factory and assembly lines.
The -E model can be used in extreme environments with an operating temperature range of -40°C to 75°C.
|8350-606||IPGS-5408GSFP||8 10/100/1000T PoE at/af + 4 1000M SFP L2+ Industrial Managed Ethernet Switch w/USB; -20°C to 60°C|
|8350-607||IPGS-5408GSFP-E||8 10/100/1000T PoE at/af + 4 1000M SFP L2+ Industrial Managed Ethernet Switch w/USB; -40°C to 75°C|
|8350-608||IPGS-5408GSFP-M||8 10/100/1000T PoE at/af + 4 1000M SFP L2+ Industrial Managed Ethernet Switch w/USB & Environmental monitoring; -20°C to 60°C|
|8350-609||IPGS-5408GSFP-M-E||8 10/100/1000T PoE at/af + 4 1000M SFP L2+ Industrial Managed Ethernet Switch w/USB & Environmental monitoring; -40°C to 75°C|
|NDR-480 Series||480W Single Output Industrial Din Rail Power; 90-264VAC / 127-370VDC Input Range; Cooling by free air convection; RoHS2 ; Operating Temp. -20°C~70°C (ambient, derating each output at 2.5% per degree from 50°C ~ 70°C)|
|NDR-240 Series||240W Single Output Industrial Din Rail Power; 90-264VAC / 127-370VDC Input Range; Cooling by free air convection; RoHS2 ; Operating Temp. -20°C~70°C (ambient, derating each output at 2.5% per degree from 50°C ~ 70°C)|
|NDR-120 Series||120W Single Output Industrial Din Rail Power; 90-264VAC / 127-370VDC Input Range; Cooling by free air convection; RoHS2 ; Operating Temp. -20°C~70°C (ambient, derating each output at 2.5% per degree from 50°C ~ 70°C; For 115VAC, please refer to derating curve on NDR-120 Series datasheet)|
|NDR-75 Series||75W Single Output Industrial Din Rail Power; 90-264VAC / 127-370VDC Input Range; Cooling by free air convection; RoHS2 ; Operating Temp. -20°C~70°C (ambient, derating each output at 2.5% per degree from 50°C ~ 70°C; For 115VAC, please refer to derating curve on NDR-120 Series datasheet)|
|Model name||Description||Model name||Description|
|8330-188-V1||LTSFP-1000BX-10KM Transceiver (WDM 1310)||8330-162-V1||MINI GBIC 1000SX (LC/0.5km) Transceiver|
|8330-189-V1||LTSFP-1000BX-10KM Transceiver (WDM 1550)||8330-163-V1||MINI GBIC 1000SX2 (LC/2km) Transceiver|
|8330-186-V1||LTSFP-1000BX-20KM Transceiver (WDM 1310)||8330-165-V1||MINI GBIC 1000LX (LC/10km) Transceiver|
|8330-187-V1||LTSFP-1000BX-20KM Transceiver (WDM 1550)||8340-0591-V1||MINI GBIC 1000LHX (LC/40km) Transceiver|
|8330-180-V1||LTSFP-1000BX-40KM Transceiver (WDM 1310)||8330-166-V1||MINI GBIC 1000XD (LC/50km) Transceiver|
|8330-182-V1||LTSFP-1000BX-40KM Transceiver (WDM 1550)||8330-169-V1||MINI GBIC 1000XD (LC/60km) Transceiver|
|8330-181-V1||LTSFP-1000BX-60KM Transceiver (WDM 1310)||8330-167-V1||MINI GBIC 1000ZX (LC/80km) Transceiver|
|8330-183-V1||LTSFP-1000BX-60KM Transceiver (WDM 1550)||8330-170-V1||MINI GBIC 1000EZX (120km) Transceiver|
|8330-184-V1||LTSFP-1000BX-80KM Transceiver (WDM 1490)||8330-168-V1||MINI GBIC 1000T (100m) Transceiver|
|8330-185-V1||LTSFP-1000BX-80KM Transceiver (WDM 1550)||All SFP P/N# ended with D are with DDM function|
|MBAK19003||Wall mount bracket for 74(W) x 105 (D) x 152 (H) mm / 96 (W) x 105 (D) x 152 (H) mm Industrial switches|
|MBAK19004||19” Rack Mounting Kit for 74x105x152mm/74x135x152mm Industrial Switch|