- ABOUT LANTECH
- PRODUCTS
Software Package
Hardened Ethernet Connections
- EN50155 10G Uplinks Managed Ethernet Switches
- EN50155 2.5G Uplinks Managed Ethernet Switches
- EN50155 Giga Uplinks Managed Ethernet Switches
- EN50155 Unmanaged Ethernet Switches
- EN50155 Multifunction 4G+WiFi Routers
- EN50155 IEC 61375 Ethernet Switches
- Industrial IEC 61850-3 PT Switches
- Industrial E-marking Switches & Routers
- Industrial DNV Type Switches
- Industrial Hazardous Switches
- Industrial Managed Switches
- Industrial 10G Switches
- Industrial 2.5G Switches
- Industrial Rackmount Switches
- Industrial PoE Solutions
- Industrial Unmanaged Switches
- Industrial Multifunction 4G+WiFi Routers
- Industrial Converter Series
- Industrial / Serial Devices
Software / Accessories
Naming Rule
- SOLUTIONS
- CASE STUDY
- SUPPORT
- CONTACT US
16 10/100TX + 4 1G/2.5G Copper w/8/10/16 PoE at/af EN50155 OS3 Managed Ethernet Switch w/ Enhanced G.8032 Ring; PXE; WVI input
- Total 16 Port 10/100TX + 4 1G/2.5G
Copper Ethernet Switch w/8/16 or 10 (incl.8 copper + 2 uplink 1G/2.5G copper)
PoE ports
- Support IEEE802.3at/af up to 30W per
port PoE management incl. Detection and Scheduling
- Support PXE to verify switch firmware
with the latest or certain version on server
- Enhanced G.8032 ring protection < 20ms
for single ring. Supports enhanced mode and basic mode; Enhanced G.8032 ring
covers multicast packets; MSTP 8 MSTI /RSTP; support MRP ring
- Miss-wiring avoidance & node failure
protection
- User friendly UI, including auto
topology drawing; Complete CLI
- Support LACP link aggregation, IGMP
v3/router port, MLD snooping, DHCP server & DHCP Option82; Port based DHCP
distribution, Mac based DHCP server, SSH v2/SSL, HTTPS, INGRESS ACL L2/L3,
TACACS+, QinQ, QoS by VLAN
- Protocol based VLAN; IPv4 Subnet based
VLAN
- Optional L3Lite or IEC 61375-2-5 TBN
features to be upgradable
- Enhanced Environmental Monitoring for
temp., actual input voltage, current & total power load
- Optional smart bypass on 1G/2.5G Copper
ports in case of power failure, CPU hang (up to two pairs)
- IP54 Aluminum housing for best heat
dissipation and preventing moist ingress
- USB port to upload & download the
configuration file
- Inrush current protection
- Dual power input 16.8V~137.5V with
galvanic isolation between input power, PoE and system
- Factory reset pin to restore to factory
default setting
- Wide range operation temperature:
-40~70C/-40~158F
Datasheet
Hardware
Manual
For latest firmware and web UI user manual, please send request to sales@lantechcom.com.au
OVERVIEW
Lantech TPES-L5416MGT is a high performance OS3 Ethernet switch with 16 10/100TX + 4 1G/2.5G Copper w/8/16 or w/10 (incl.8 copper + 2 uplink 1G/2.5G copper) PoE 802.3af/at Ports which provides advanced security function for network aggregation deployment. It delivers ITU G.8032 enhanced ring recovery less than 20ms in single ring. The QoS, advanced security including INGRESS ACL L2/L3, TACACS+, SSH v2/SSL and subnet VLAN, protocol VLAN and Mac based DHCP server, DHCP Option 82, DHCP server, IGMPv1/v2/v3/router port are supported and also required in large network. It also supports10K Jumbo frames.
Up to 8/10/16 PoE at/af ports w/advanced PoE management
Compliant with 802.3af/at standard, the Lantech TPES-L5416MGT is able to feed each PoE port
up to 30 Watt at each PoE port for various IP PD devices. Lantech TPES-L5416MGT supports
advanced PoE management including PoE detection and scheduling. PoE detection can detect if
the connected PD hangs then restart the PD; PoE scheduling is to allow pre-set power feeding
schedule upon routine time table. Each PoE port can be Enabled/disabled, get the voltage,
current, Watt, and temperature info displayed on WebUI.
Support PXE to verify switch firmware with the latest or certain version
The switch can check its firmware version during booting time via PXE protocol. If switch
finds any newer version, it will upload automatically.
Miss-wiring avoidance, Node failure protection, Loop protection
The TPES-L5416MGT is also embedded with several features for stronger and reliable network
protection in an easy and intuitive way. When the pre-set ring configuration failed or
looped by miss-wiring, Lantech TPES-L5416MGT is able to send alert with the LED indicator
and disable ring automatically.
Node failure protection ensures the switches in a ring to survive after power breakout is
back. The status can be shown in NMS when each switch is back. This feature prevents the
broken ring and keep ring alive without any re-configuration needed.
Loop protection is also available to prevent the generation of broadcast storm when a dumb
switch is inserted in a closed loop connection.
DHCP option 82 & Port based, Mac based DHCP, Option66, IPv6 DHCP
server
DHCP server can assign dedicated IP address by MAC or by port (Port based for single
switch), it also can assign IP address by port for multiple switches with single DHCP
option82 server. DHCP Option66 server can offer IP address of TFTP server to DHCP client for
VOIP application. Basic IPv6 DHCP service can be supported.
User friendly GUI, Auto topology drawing
The user-friendly UI, innovative auto topology drawing and topology demo makes TPES-L5416MGT
much easier to get hands-on. The complete CLI enables professional engineer to configure
setting by command line.
Protocol based VLAN; Subnet based VLAN
The protocol-based VLAN processes traffic based on protocol. It filters IP traffic from
nearby end-stations using a particular protocol such as IP, IPX, ARP or other Ethernet-types
in a Hex value. Subnet based VLANs group traffics into logical VLANs based on the source IP
address and IP subnet.
The above features can help to build VLAN in the network mixed with managed and un-managed
switch as to define packets to which VLAN group based on protocol or subnet.
Enhanced G.8032 ring, 8 MSTI MSTP; MRP ring
Lantech TPES-L5416MGT features enhanced G.8032 ring which can be self-healed in less than
20ms for single ring topology protection covering multicast packets. It also supports
various ring topologies that covers enhanced ring and basic ring by easy setup than others.
It supports MSTP that allows RSTP over VLAN for redundant links with 8 MSTI.
MRP (Media Redundancy Protocol) can be supported for industrial automation networks.
Built-in IEC 61375-3-4 ECN (Ethernet Consist Network) to work with IEC61375-2-5
TBN
Lantech OS3 Ethernet switches comply with IEC 61375-3-4 (ECN) standard. The support of
Ethernet Consist Network allows interconnection between end devices located in single
consist of train and interoperability with IEC61375-2-5 (TBN).
Enhanced Storm control*
Storm control prevents traffic on a LAN from being disrupted by a broadcast, multicast, or
unicast storm on one of the physical interfaces and the detection is more precise and
reaction is more efficient.
Optional L3Lite/L3*/ETBN to be upgradable
Lantech OS3 are optional upgradable to L3 Lite/ L3* or ETBN communication protocols for
future expansion. The optional L3Lite includes editable routing table, VRRP,
Router-on-a-stick, Inter- VLAN routing. Optional ETBN complies with IEC61375-2-5 ETBN for
Train Backbone Network.
QinQ, QoS and GVRP supported
It supports the QinQ, QoS and GVRP for large VLAN segmentation.
IGMPv3, GMRP, router port, MLD Snooping, static multicast forwarding and
multicast Ring protection
The unique multicast protection under enhanced G.8032 ring can offer immediate self-recovery
instead of waiting for IGMP table timeout. It also supports IGMPv3, GMRP, router port, MLD
snooping and static multicast forwarding binding by ports for video surveillance
application.
Editable configuration file; USB port for upload/download the
configuration
The configuration file of Lantech TPES-L5416MGT can be exported and edited with word
processor for the following switches to configure with ease. The factory reset button can
restore the setting back to factory default and built-in watchdog design can automatically
reboot the switch when CPU is found dead.
The USB port can upload/download the configuration from/to USB dongle.
Event log & message; 2 DI + 2DO
In case of event, the TPES-L5416MGT is able to send an email** to pre-defined addresses as
well as SNMP Traps out immediately. It provides 2DI and 2DO. When disconnection of the
specific port was detected; DO will activate the signal LED to alarm. DI can integrate the
sensors for events and DO will trigger the outside alarm and switch will send alert
information to IP network with email and traps.
Enhanced environmental monitoring for switch inside information
The enhanced environmental monitoring can detect switch overall temperature, total power
load, actual input voltage and current. It also can send the SNMP traps and email** when
abnormal.
Dual WVI input with max PoE budget and Inrush current
protection
The TPES-L5416MGT WVI model accept 16.8~137.5VDC dual input with galvanic protection and can
feed 54V output for PoE feeding with 80W budget. A voltage which can be minimal 0,5 Un
nominal voltage (when Vin≧36V) and/or a voltage which can be maximal 1,5 Un nominal voltage
for more than 1000 consecutive ms (one second).
The inrush current on initial power up can be limited lower than 10 x nominal current and
for less than 1ms.
Optional smart bypass protection on dual 1G/2.5G copper ports**
The bypass relay is set to bypass the switch to the next one when power is off to prevent
network disruption. Lantech bypass caters to remain in bypass mode until the switch is
completely booting up when power is back to avoid another network lost. Optional smart
bypass (Up to two pairs) can be activated when switch encounters power failure or CPU hang.
(-BT/-BBT model)
EN50155, EN45545-2, EN61373 verification; High ESD protection
TPES-L5416MGT passed tests under extensive Industrial EMI and Safety standards. With
EN45545-2 Fire & Smoke, EN50155 verification, the TPES-L5416MGT is best switch for railway
on-board/track side, vehicle and mining applications. For more usage flexibilities,
TPES-L5416MGT supports wide operating temperature from -40°C to 70°C. (85°C operation for
10min.)
*Future release
**Optional
FEATURES
- 16 10/100TX + 4 1G/2.5G Copper Ethernet Switch w/8/16 or 10 (8 copper + 4 uplink 1G/2.5G copper) PoE 802.3af/at ports (Total 20 Ports Switch) to feed power up to 30W for active mode operation
- Dual WVI input (16.8V~137.5VDC) for PoE budget 80W
- PoE management including PoE detection and scheduling for PD (power devices)
- Galvanic isolation from power input/Ethernet ports to system 1.5KV
- Back-plane (Switching Fabric): 23.2Gbps
- 16K MAC address table
- 10KB Jumbo frame
- User friendly UI, auto topology drawing, topology demo, complete CLI for professional setting
- Enhanced G.8032 Ring protection in 20ms for single ring
- Support various ring/chain topologies, including enhanced ring, basic ring
- Cover multicast and data packets protection
- Supports IEEE 802.1p Class of Service, per port provides 8 priority queues Port base, Tag Base and Type of Service Priority
- IEEE 802.1d STP, IEEE 802.1w RSTP,802.1s MSTP VLAN redundancy with 8 MSTI
- 4K 802.1Q VLAN, Port based VLAN, GVRP, QinQ, QoS
- Supports IEEE 802.1ab LLDP, Cisco CDP; LLDP info can be viewed via Web/ Console
- Support PXE to verify switch firmware with the latest or certain version
- DHCP server / client / DHCP Option 82 relay / DHCP Option 82 server; Port based DHCP server; DHCP Option 66; basic IPv6 DHCP server
- Mac based DHCP server to assign IP address
- Bandwidth Control
- Ingress packet filter and egress* rate limit
- Broadcast/multicast packet filter control
- Miss-wiring avoidance
- LED indicator
- Node failure protection
- Ensure the switches in a ring to survive after power breakout is back
- The status can be shown in NMS when each switch is back
- System Event Log, SMTP alert and SNMP Trap for alarm support
- Security
- SSL/SSH v2/INGRESS ACL L2/L3
- MAC address table: MAC address entries/Filter/static MAC-Port binding
- Remote Admin: IP address security management to prevent unauthorized intruder.
- TACACS+
- Login Security: IEEE802.1X/RADIUS
- HTTPS for secure access to the web interface
- Static multicast forwarding forward reversed IGMP flow with multicast packets binding with ports for IP surveillance application
- IGMP router port for multicast protection
- IGMPv1,v2,v3 with Query mode for multi media
- Dual image firmware support
- MLD Snooping for IPv6 Multicast stream
- Supports 2DI/2DO (Digital Input/Digital Output)
- Factory reset pin to restore setting to factory default
- Watchdog design to auto reboot switch when CPU is found dead
- Enhanced environmental monitoring for system actual input voltage, current, ambient temperature and total power load
- Subnet VLAN and protocol VLAN
- Configuration backup and restoration
- Supports editable configuration file for system quick installation
- USB port for upload/download the configuration file
- TFTP/HTTP firmware upgrade
- Wide operation temperature: -40C~70C/-40F~158F (85°C operation for 10min.)
- Inrush current protection
- Optional smart bypass (Up to two pairs) (-BT/-BBT model)
- Built-in IEC 61375-3-4 ECN (Ethernet Consist Network) to work with IEC61375-2-5 TBN
- Diagnostic including Ping / ARP table / DDM information
- Enhanced Storm Control*
- Optional L3Lite/L3*/ETBN to be upgradable
- EN45545-2 Fire & Smoke, EN50155 and EN61373 shock/vibration verification
- IP54 aluminum housing with wall mount design
*Future release
**Optional
SPECIFICATIONS
Hardware Specifications
|
Standards |
IEEE802.3 10Base-T Ethernet |
|||||||||
|
Switch Architecture |
Back-plane (Switching Fabric): 23.2Gbps |
|||||||||
|
Mac Address |
16K MAC address table |
|||||||||
|
Jumbo frame |
10KB |
|||||||||
|
Connectors |
10/100TX: 16 x M12 4-pole D-coded with Auto MDI/MDI function |
|||||||||
|
Network Cable |
10Base-T: 2-pair STP Cat. 3, 4, 5/ 5E/ 6 cable |
|||||||||
|
LED |
Per unit: Power 1 (Green), Power 2 (Green), FAULT (Red);
RM(Green) |
|||||||||
|
DI/DO |
2 Digital Input (DI): |
|||||||||
|
Operating Humidity |
5% ~ 95% (Non-condensing) |
|||||||||
|
Operating Temperature |
-40°C~70°C / -40°F~158°F |
|||||||||
|
Storage Temperature |
-40°C~85°C / -40°F~185°F |
|||||||||
|
Power Supply |
Dual DC input, 16.8VDC~137.5VDC |
|||||||||
|
PoE Budget |
|
|||||||||
|
PoE pin assignment |
M12 port #1~#8/16 (-8/-16 model) ; #17~#18 (-10 model) ; support IEEE
802.3at/af End-point, Alternative A mode |
|||||||||
|
Power Consumption |
Max. 39.5W (exclude PoE load) |
|||||||||
|
Case Dimension |
IP54 model: Aluminum case |
|||||||||
|
Weight |
1.8kgs |
|||||||||
|
Installation |
Wall Mount Design |
|||||||||
|
EMI & EMS |
FCC Part 15 Class A, |
|||||||||
|
Verifications |
EN50155/EN50121-3-2/EN50121-4 verification |
|||||||||
|
Stability Testing |
EN61373 (Shock and Vibration) |
|||||||||
MTBF |
447,857 hrs (standards: IEC 62380) |
|||||||||
|
Warranty |
5 years |
|||||||||
|
Bypass** |
Up to two pairs bypass module on 1G/2.5G Copper ports to pass to next switch in case of power failure and CPU fail |
Software Specifications
|
Management |
SNMP v1 v2c, v3/ Web/Telnet/CLI |
|
SNMP MIB |
RFC 1213 MIBII |
|
ITU G.8032 |
Support ITU G.8032 for Ring protection in less than 20ms for
self-heal recovery (single ring) |
|
PoE Management |
PoE Detection to check if PD hangs then restart the PD |
|
Per Port PoE Status |
On/ Off, voltage, current, watts, temperature |
|
User friendly UI |
|
|
Port Trunk with LACP |
LACP Port Trunk: 8 Trunk groups |
|
LLDP |
Supports LLDP to allow switch to advise its identification and capability on the LAN |
|
CDP |
Cisco Discovery Protocol for topology mapping |
|
Enhanced Environmental Monitoring |
System status for actual input voltage, current, total power load and ambient temperature to be shown in GUI and send alerting if any abnormal status |
|
VLAN |
Port Based VLAN |
|
Spanning Tree |
Supports IEEE802.1d Spanning Tree and IEEE802.1w Rapid Spanning Tree, IEEE802.1s Multiple Spanning Tree 8 MSTI |
|
Quality of Service |
The quality of service determined by port, Tag and IPv4 Type of service, IPv4 Differentiated Services Code Points – DSCP |
|
Class of Service |
Support IEEE802.1p class of service, per port provides 8 priority queues |
|
Remote Admin |
Supports 10 IP addresses that have permission to access the switch management and to prevent unauthorized intruder. |
|
Login Security |
Supports IEEE802.1X Authentication/RADIUS |
|
Port Mirror |
Support 3 mirroring types: “RX, TX and Both packet” |
|
Network Security |
Support 10 IP addresses that have permission to access the switch
management and to prevent unauthorized intruder. |
|
MLD Snooping |
Support IPv6 Multicast stream |
|
IGMP |
Support IGMP snooping v1,v2,v3; Supports IGMP static forwarding; 1024 multicast groups; IGMP router port ; IGMP query; GMRP |
|
Static multicast forwarding |
Static multicast forwarding forward reversed IGMP flow with multicast packets binding with ports for IP surveillance application |
|
Bandwidth Control |
Support ingress packet filter and egress* packet limit. |
|
Flow Control |
Supports Flow Control for Full-duplex and Back Pressure for Half-duplex |
|
System Log |
Supports System log record and remote system log server |
|
Protection |
|
|
SNMP Trap |
Up to 5 trap stations; trap types including:
|
|
PXE |
PXE to verify switch firmware with the latest or certain version |
|
DHCP |
Provide DHCP Client/ DHCP Server/DHCP Option 82/Port based DHCP; DHCP Option 66; basic IPv6 DHCP server |
|
Mac based DHCP Server |
Assign IP address by Mac that can include dumb switch in DHCP network |
|
DNS |
Provide DNS client feature and can set Primary and Secondary DNS server. |
|
NTP/SNTP |
Supports NTP/SNTP to synchronize system clock in Internet |
|
Enhanced Storm Control* |
prevents traffic on a LAN from being disrupted by a broadcast, multicast, or unicast storm on one of the physical interfaces |
|
ECN |
Complies with IEC 61375-3-4 (ECN) standard. The support of Ethernet Consist Network allows interconnection between end devices located in single consist of train and interoperability with IEC61375-2-5 (TBN). |
|
Optional L3Lite/L3*/ETBN |
Lantech OS3 are optional upgradable to L3 Lite/ L3* or ETBN
communication protocols for future expansion. The optional L3Lite
includes editable routing table, VRRP, Router-on-a-stick, Inter-
VLAN routing. Optional ETBN complies with IEC61375-2-5 ETBN for
Train Backbone Network. |
|
Firmware Update |
Supports TFTP firmware update, TFTP backup and restore; HTTP firmware upgrade |
|
Configuration |
Supports editable configuration file for system quick installation; Support factory reset pin to restore all settings back to factory default |
|
Diagnostic |
Support Ping, ARP table and DDM information |
|
Dual Image Firmware |
Support dual image firmware function |
*Future release
**Optional
DIMENSION
ORDER INFORMATION
All model packages include M12 caps and wall mount bracket. All standard models are non-coating, optional coating models are available with –C model name; For optional bypass add –BT (one pair); -BBT (two pairs) to end of model name.
| P/N | Model name | Description |
|---|---|---|
| 8361-4707 | TPES-L5416MGT-8-54-WVI | 16 10/100TX + 4 1G/2.5G Copper M12 X-coded w/8 PoE 802.3at/af EN50155 OS3 PoE Managed Ethernet Switch; 16.8V~137.5VDC dual input; -40~70C/-40~158F; IP54 housing w/ galvanic isolation |
| 8361-6272 | TPES-L5416MGT-8-54-WVI-BT | 16 10/100TX + 4 1G/2.5G Copper M12 X-coded w/8 PoE 802.3at/af EN50155 OS3 PoE Managed Ethernet Switch; 16.8V~137.5VDC dual input; -40~70C/-40~158F; IP54 housing w/ galvanic isolation; one-pair copper bypass |
| 8361-6274 | TPES-L5416MGT-8-54-WVI-BBT | 16 10/100TX + 4 1G/2.5G Copper M12 X-coded w/8 PoE 802.3at/af EN50155 OS3 PoE Managed Ethernet Switch; 16.8V~137.5VDC dual input; -40~70C/-40~158F; IP54 housing w/ galvanic isolation; two-pairs copper bypass |
| 8361-627 | TPES-L5416MGT-10-54-WVI | 16 10/100TX + 4 1G/2.5G Copper M12 X-coded w/10 PoE 802.3at/af incl. 2 1G/2.5G copper EN50155 OS3 PoE Managed Ethernet Switch; 16.8V~137.5VDC dual input; -40~70C/-40~158F; IP54 housing w/ galvanic isolation |
| 8361-6271 | TPES-L5416MGT-16-54-WVI | 16 10/100TX + 4 1G/2.5G Copper M12 X-coded w/16 PoE 802.3at/af EN50155 OS3 PoE Managed Ethernet Switch; 16.8V~137.5VDC dual input; -40~70C/-40~158F; IP54 housing w/ galvanic isolation |
OPTIONAL ACCESSORIES - Software package
| P/N | Model name | Description |
|---|---|---|
| 9000-114 | OS3 – L3L | OS3 software platform with Layer 3 Lite functions (please check Lantech software data sheet for details) |
| 9000-115 | OS3 – IEC61375-2-5 | OS3 software platform with IEC-61375-2-5 ETBN (Ethernet Train Backbone Networks) functions incl. L3L (please check Lantech software data sheet for details) |
| 9000-116 | OS3 – L3* | OS3 software platform with Layer 3 functions incl. IEC61375-2-5 and L3L (please check Lantech software data sheet for details) |
OPTIONAL ACCESSORIES - Connector
| Model name | Description |
|---|---|
| ECONM12-04A(F)-C-180 | 4 pin M12 (Female) A-coded 180 degree crimp type connector for power supply |
| ECONM12-08A(M)-180 | 8 pin M12 (Male) A-coded 180 degree crimp type connector for reset/console/USB |
| ECONM12-05A(M)-C-180 | 5 pin M12 (Male) A-coded 180 degree crimp type connector for DI/DO |
| ECONM12-08X(M)-SPEEDCON | 8 pin M12 (Male) X-coded 180 degree crimp type connector for data, Ethernet CAT6A (10G), shielded, SPEEDCON |
OPTIONAL ACCESSORIES - Cable
| Model name | Description |
|---|---|
| ECONM12-4P(F)1.5M CABLE | 4 pin M12 (Female) A-coded 90 degree cable for power supply, 150cm |
| ECONM12-08M2-CONSOLE | 8 pin M12 (Male) A-coded 180 degree to RS232 cable for console, 150cm |
| ECABM12X83MSTP | 8 pin M12 (Male) X-coded 180 degree RJ45 STP cable for data, shielded, 300cm |
OPTIONAL ACCESSORIES - Others
| Model name | Description |
|---|---|
| USB adapter (8850-102) | 8 pin M12 (Male) A-coded 180 degree M12 to USB 2.0 interface adapter, 8cm |
| USB adapter set (8850-103) | 8 pin M12 (Male) A-coded 180 degree M12 to USB 2.0 to DB9 (Female) Cable, 150cm + USB NIC |
