16 10/100/1000T w/8 (16) PoE at/af EN50155 OS3 Managed Ethernet Switch w/ Enhanced G.8032 Ring; PXE; WVI input

  • Total 16 Port GT Ethernet Switch w/ 8(16) PoE ports
  • Support IEEE802.3at/af up to 30W per port PoE management incl. Detection and Scheduling
  • Support PXE to verify switch firmware with the latest or certain version on server
  • Enhanced G.8032 ring protection < 20ms for single ring. Supports enhanced mode and basic mode; Enhanced G.8032 ring covers multicast packets; MSTP 8 MSTI /RSTP ; support MRP ring
  • Miss-wiring avoidance & node failure protection
  • User friendly UI, including auto topology drawing; Complete CLI
  • Support LACP link aggregation, IGMP v3/router port, DHCP server & DHCP Option82; Port based DHCP distribution, Mac based DHCP server, SSH/SSL, HTTPS, INGRESS/EGRESS* ACL L2/L3,TACACS+, subnet VLAN and protocol VLAN
  • Environmental Monitoring for temp., actual input voltage, current & total power load
  • IP54 Aluminum housing for best heat dissipation and preventing moist ingress
  • USB port to upload & download the configuration file
  • Dual power input 16.8V~137.5V with galvanic isolation between input power, PoE and system
  • Factory reset pin to restore to factory default setting
  • Wide range operation temperature :-40~70C/-40~167F

Datasheet   Hardware Manual   Web UI User's Manual
For latest firmware, please send request to support@lantechcom.com.au


Lantech TPGS-L5016T-8(16)(IP54) is a high performance OS3 (All Gigabit) Ethernet switch with 16 10/100/1000T w/8(16) PoE 802.3af/at ports which provides advanced security function for network aggregation deployment. It delivers ITU G.8032 enhanced ring recovery less than 20ms in single ring. The QoS, advanced security including INGRESS/EGRESS* ACL L2/L3, TACACS+, SSH/SSL and Mac based DHCP server, DHCP Option 82, DHCP server, IGMPv1/v2/v3/router port are supported and also required in large network. It also supports10K Jumbo frames.

Up to 8/16 PoE at/af ports w/advanced PoE management
Compliant with 802.3af/at standard, the Lantech TPGS-L5016T-8(16)(IP54) is able to feed each PoE port up to 30 Watt. Lantech TPGS-L5016T-8(16) (IP54) supports advanced PoE management including PoE detection and scheduling. PoE detection can detect if the connected PD hangs then restart the PD; PoE scheduling is to allow pre-set power feeding schedule upon routine time table. Each PoE port can be Enabled/disabled, get the voltage, current, Watt, and temperature info displayed on WebUI.

Support PXE to verify switch firmware with the latest or certain version
The switch can check its firmware version during booting time via PXE protocol. If switch finds any newer version, it will upload automatically.

Miss-wiring avoidance, Node failure protection, Loop protection
The TPGS-L5016T-8(16) (IP54) is also embedded with several features for stronger and reliable network protection in an easy and intuitive way. When the pre-set ring configuration failed or looped by miss-wiring, Lantech TPGS-L5016T-8(16) (IP54) is able to send alert with the LED indicator and disable ring automatically.

Node failure protection ensures the switches in a ring to survive after power breakout is back. The status can be shown in NMS when each switch is back. This feature prevents the broken ring and keep ring alive without any re-configuration needed.

Loop protection is also available to prevent the generation of broadcast storm when a dumb switch is inserted in a closed loop connection.

DHCP option 82 & Port based, Mac based DHCP, Option66, IPv6 DHCP server
DHCP server can assign dedicated IP address by MAC or by port (Port based for single switch) , it also can assign IP address by port for multiple switches with single DHCP option82 server. DHCP Option66 server can offer IP address of TFTP server to DHCP client for VOIP application. IPv6 address resolution for basic DHCP service can be supported.

User friendly GUI, Auto topology drawing
The user friendly UI, innovative auto topology drawing and topology demo makes TPGS-L5016T-8(16) (IP54) much easier to get hands-on. The complete CLI enables professional engineer to configure setting by command line.

Enhanced G.8032 ring, 8 MSTI MSTP; MRP ring
Lantech TPGS-L5016T-8(16)(IP54) features enhanced G.8032 ring which can be self-healed in less than 20ms for single ring topology protection covering multicast packets. It also supports various ring topologies that covers enhanced ring and basic ring by easy setup than others. It supports MSTP that allows RSTP over VLAN for redundant links with 8 MSTI.

MRP (Media Redundancy Protocol) can be supported for industrial automation networks.

IGMPv3, GMRP, router port, MLD Snooping, static multicast forwarding and multicast Ring protection
The unique multicast protection under enhanced G.8032 ring can offer immediate self-recovery instead of waiting for IGMP table timeout. It also supports IGMPv3, GMRP, router port, MLD snooping and static multicast forwarding binding by ports for video surveillance application.

Editable configuration file; USB port for upload/download the configuration
The configuration file of Lantech TPGS-L5016T-8(16) (IP54) can be exported and edited with word processor for the following switches to configure with ease. The factory reset button can restore the setting back to factory default and built-in watchdog design can automatically reboot the switch when CPU is found dead.

The USB port can upload/download the configuration from/to USB dongle.

Event log & message; 2 DI + 2DO
In case of event, the TPGS-L5016T-8(16)(IP54) is able to send an email** & SMS** text message to pre-defined addresses as well as SNMP Traps out immediately. It provides 2DI and 2DO. When disconnection of the specific port was detected; DO will activate the signal LED to alarm. DI can integrate the sensors for events and DO will trigger the outside alarm and switch will send alert information to IP network with email and traps.

Environmental monitoring for switch inside information
The environmental monitoring can detect switch overall temperature, total power load, actual input voltage and current. It also can send the SNMP traps, email** and SMS** alert when abnormal.

Protocol based VLAN; Subnet based VLAN
The protocol-based VLAN processes traffic based on protocol. It filters IP traffic from nearby end-stations using a particular protocol such as IP, IPX, ARP or other Ethernet-types in a Hex value. Subnet based VLANs group traffics into logical VLANs based on the source IP address and IP subnet. The above features can help to build VLAN in the network mixed with managed and un-managed switch as to define packets to which VLAN group based on protocol or subnet based.

Dual WVI (16.8V~137.5VDC) isolated input, High PoE budget
WVI model accepts 16.8~137.5VDC dual input and can feed 54V output for PoE feeding with max 80W. The galvanic isolation protects system and PoE from surge or EFT under 1.5KV.

EN50155, EN45545-2, EN61373 verification
TPGS-L5016T-8(16) (IP54) passed tests under extensive Industrial EMI and Safety standards. With EN45545-2 Fire & Smoke, EN50155 verification, the TPGS-L5016T-8(16) (IP54) is best switch for railway on-board/track side, vehicle and mining applications. For more usage flexibilities, TPGS-L5016T-8(16) (IP54) supports wide operating temperature from -40°C to 75°C.

*Future release


  • 16 10/100/1000T Ethernet Switch w/8(16) PoE 802.3af/at ports (Total 16 Ports Switch)
  • Embedded 8/16 PoE Injectors IEEE802.3af/at function to feed power up to 30W for active mode operation
  • Max PoE budget 80W
  • PoE management including PoE detection and scheduling for PD (power devices)
  • Back-plane (Switching Fabric):32Gbps
  • 16K MAC address table
  • 10KB Jumbo frame
  • User friendly UI, auto topology drawing, topology demo, complete CLI for professional setting
  • Enhanced G.8032 Ring protection in 20ms for single ring
    • Support various ring/chain topologies, including  enhanced ring, basic ring
    • Cover multicast and data packets protection
  • Supports IEEE 802.1p Class of Service, per port provides 8 priority queues Port base, Tag Base and Type of Service Priority
  • IEEE 802.1d STP, IEEE 802.1w RSTP,802.1s MSTP VLAN redundancy with 8 MSTI
  • 4K 802.1Q VLAN, Port based VLAN, GVRP
  • Supports IEEE 802.1ab LLDP, Cisco CDP; LLDP info can be viewed via Web/ Console
  • Support PXE to verify switch firmware with the latest or certain version
  • DHCP server / client / DHCP Option 82 relay / DHCP Option 82 server; Port based DHCP server; DHCP Option 66; IPv6 address resolution for DHCP server
  • Mac based DHCP server to assign IP address
  • Bandwidth Control
    • Ingress packet filter and egress rate limit
    • Broadcast/multicast packet filter control
  • Miss-wiring avoidance
    • LED indicator
  • Node failure protection
    • Ensure the switches in a ring to survive after power breakout is back
    • The status can be shown in NMS when each switch is back
  • System Event Log, SMTP alert and SNMP Trap for alarm support
  • Security
    • MAC address table: MAC address entries/Filter/static MAC-Port binding
    • Remote Admin: IP address security management to prevent unauthorized intruder.
    • TACACS+
    • Login Security: IEEE802.1X/RADIUS
    • HTTPS for secure access to the web interface
  • Static multicast forwarding forward reversed IGMP flow with multicast packets binding with ports for IP surveillance application
  • IGMP router port for multicast protection
  • IGMPv1,v2,v3 with Query mode for multi media
  • Dual image firmware support
  • MLD Snooping for IPv6 Multicast stream
  • Supports 2DI/2DO (Digital Input/Digital Output)
  • Factory reset pin to restore setting to factory default
  • Watchdog design to auto reboot switch when CPU is found dead
  • Environmental monitoring for system actual input voltage, current, ambient temperature and total power load
  • Configuration backup and restoration
    • Supports editable configuration file for system quick installation
    • USB port for upload/download the configuration file
  • TFTP/HTTP firmware upgrade
  • Wide operation temperature: -40C~75C/-40F~167F
  • Dual WVI isolated input from 16.8V~137.5VDC
  • Galvanic isolation protects system and PoE under 1.5KV
  • Subnet VLAN and protocol VLAN
  • EN45545-2 Fire & Smoke, EN50155 and EN61373 shock/vibration verification
  • IP54 aluminum housing with wall mount design
*Future release


Hardware Specifications


IEEE802.3 10Base-T Ethernet
IEEE802.3u 100Base-TX
IEEE802.3ab 1000Base-T
IEEE802.3z Gigabit fiber
IEEE802.3x Flow Control and Back Pressure
IEEE802.3ad Port trunk with LACP
IEEE802.1d Spanning Tree
IEEE802.1w Rapid Spanning Tree
IEEE802.1s Multiple Spanning Tree
IEEE802.3ad Link Aggregation Control Protocol (LACP)
IEEE802.1AB Link Layer Discovery Protocol (LLDP)
IEEE802.1X User Authentication (Radius)
IEEE802.1p Class of Service
IEEE802.3at/af Power over Ethernet

Switch Architecture

Back-plane (Switching Fabric): 32Gbps

Mac Address

16K MAC address table

Jumbo frame



10/100/1000T: 16 x M12 8-pole X-coded with Auto MDI/MDI function
Power Input connector: 1 x M12 4-pole A-coded
Reset/Console/USB : 1 x M12 8-pole A-coded
DIDO: 1 x M12 5-pole A-coded

Network Cable

10Base-T: 2-pair STP Cat. 3, 4, 5/ 5E/ 6 cable
EIA/TIA-568 100-ohm (100m)
100Base-TX: 2-pair STP Cat. 5/ 5E/ 6 cable; EIA/TIA-568 100-ohm (100m)
1000Base-T: 4-pair STP Cat5E/6 cable


Per unit: Power 1 (Green), Power 2 (Green), FAULT (Red); RM(Green)
Ethernet port: Link/Activity (Green)
PoE : Link/Act (Green)


2 Digital Input (DI) :
Level 0: -30~2V / Level 1: 10~30V
Max. input current:8mA
Digital Output (DO): Open collector to 80 VDC, 50mA

Operating Humidity

5% ~ 95% (Non-condensing)

Operating Temperature

-40°C~75°C / -40°F~167°F

Storage Temperature

-40°C~85°C / -40°F~165°F

Power Supply

Dual DC isolated input, 16.8VDC~137.5VDC

PoE Budget


PoE pin assignment

M12 port # 1~ # 8/16 support IEEE 802.3at/af End-point. Per port provides up to 30W

Power Consumption

Max. 33.8W (exclude PoE load)

Case Dimension

IP54 model: Aluminum case




Wall Mount Design


FCC Part 15 Class A,
CE EN55032 Class A
CE EN55024: CE EN61000-4-2 (ESD) Level 3
CE EN61000-4-3 (RS) Level 3
CE EN61000-4-4 (EFT) Level 3
CE EN61000-4-5 ED3 (Surge) Level 3
CE EN61000-4-6 (CS) Level 3
CE N61000-4-8 (Magnetic field) Level 3


EN50155/EN50121-3-2/EN50121-4 verification
EN45545-2 R13/R22/R23/R24/R25 (EN ISO 4589-2, EN ISO 5659-2, NF X70-100-1 & 2) Fire & Smoke verification

Stability Testing

EN61373 (Shock and Vibration)


551,745 hrs (IEC 62830 standards)


5 years

Software Specifications


SNMP v1 v2c, v3/ Web/Telnet/CLI


RFC 1493 Bridge MIB*
RFC 1573 IF MIB 
RFC 2674 Q-Bridge MIB*; Bridge MIB,
Private MIB

ITU G.8032

Support ITU G.8032 for Ring protection in less than 20ms for self-heal recovery (single ring)
Support various ring/chain topologies
Includes basic single ring, enhanced ring
Cover multicast & data packets protection

PoE Management

PoE Detection to check if PD hangs then restart the PD
PoE scheduling

Per Port PoE Status

On/ Off, voltage, current, watts, temperature

User friendly UI

  1. Auto topology drawing
  2. Topology demo
  3. Complete CLI for professional setting

Port Trunk with LACP

LACP Port Trunk: 8 Trunk groups


Supports LLDP to allow switch to advise its identification and capability on the LAN


Cisco Discovery Protocol for topology mapping

Environmental Monitoring

System status for actual input voltage, current , total power load and ambient temperature to be shown in GUI and send alerting if any abnormal status


Port Based VLAN
IEEE 802.1Q Tag VLAN (256 entries)/ VLAN ID (Up to 4K, VLAN ID can be assigned from 1 to 4096)
Protocol based VLAN
Subnet based VLAN



Spanning Tree

Supports IEEE802.1d Spanning Tree and IEEE802.1w Rapid Spanning Tree, IEEE802.1s Multiple Spanning Tree 8 MSTI

Quality of Service

The quality of service determined by port, Tag and IPv4 Type of service, IPv4 Differentiated Services Code Points – DSCP

Class of Service

Support IEEE802.1p class of service, per port provides 8 priority queues

Remote Admin

Supports 10 IP addresses that have permission to access the switch management and to prevent unauthorized intruder.

Login Security

Supports IEEE802.1X Authentication/RADIUS

Port Mirror

Support 3 mirroring types: “RX, TX and Both packet”

Network Security

Support 10 IP addresses that have permission to access the switch management and to prevent unauthorized intruder.
802.1X access control for port based and MAC based authentication/static MAC-Port binding
Ingress/Egress* ACL L2/L3
SSL/ SSH for Management
HTTPS for secure access to the web interface
TACACS+ for Authentication

MLD Snooping

Support IPv6 Multicast stream


Support IGMP snooping v1,v2,v3; Supports IGMP static forwarding; 1024 multicast groups; IGMP router port ; IGMP query; GMRP

Static multicast forwarding

Static multicast forwarding forward reversed IGMP flow with multicast packets binding with ports for IP surveillance application

Bandwidth Control

Support ingress packet filter and egress packet limit.
The egress rate control supports all of packet type.
Ingress filter packet type combination rules are Broadcast/Multicast/Flooded Unicast packet, Broadcast/Multicast packet, Broadcast packet only and all types of packet.
The packet filter rate can be set an accurate value through the pull-down menu for the ingress packet filter and the egress packet limit.

Flow Control

Supports Flow Control for Full-duplex and Back Pressure for Half-duplex

System Log

Supports System log record and remote system log server


  1. Miss-wiring avoidance
  2. Node failure protection
  3. Loop protection


Up to 5 trap stations; trap types including:

  1. Device cold start
  2. Authorization failure
  3. Port link up/link down
  4. DI/DO open/close
  5. Typology change(ITU ring)
  6. Power failure
  7. Environmental abnormal


PXE to verify switch firmware with the latest or certain version


Provide DHCP Client/ DHCP Server/DHCP Option 82/Port based DHCP; DHCP Option 66; IPv6 address resolution for DHCP server

Mac based DHCP Server

Assign IP address by Mac that can include dumb switch in DHCP network


Provide DNS client feature and can set Primary and Secondary DNS server.


Supports NTP/SNTP to synchronize system clock in Internet

Firmware Update

Supports TFTP firmware update, TFTP backup and restore; HTTP firmware upgrade;

upload and download

Supports editable configuration file for system quick installation; Support factory reset pin to restore all settings back to factory default


Support Ping, ARP table and DDM information

Dual Image Firmware

Support dual image firmware function

*Future release



All model packages include M12 caps and wall mount bracket. All standard models are non-coating, optional coating models are available with –C model name.

P/N Model name Description
8361-4312 TPGS-L5016T-8-54-WVI 16 10/100/1000T M12 X-coded w/8 PoE at/af EN50155 OS3 PoE Managed Ethernet Switch; 16.8V~137.5VDC dual isolated input; PoE budget 80W; IP54 housing; -40°C to 75°C
8361-431 TPGS-L5016T-16-54-WVI 16 10/100/1000T M12 X-coded w/16 PoE at/af EN50155 OS3 PoE Managed Ethernet Switch; 16.8V~137.5VDC dual isolated input; PoE budget 80W; IP54 housing; -40°C to 75°C


P/N Model name Description
9000-114 OS3 - L3L OS3 software platform with Layer 3 Lite functions (please check Lantech software data sheet for details)
9000-115 OS3 – IEC61375-2-5 OS3 software platform with IEC-61375-2-5 ETBN (Ethernet Train Backbone Networks) function (please check Lantech software data sheet for details)
9000-116 OS3 – L3 OS3 software platform with Layer 3 functions (please check Lantech software data sheet for details)


Model name Description
ECON120005PF M12 5P(Female) A-coded 160 Degree Crimp Type Connector
ECONM12-5P(F)1.5M CABLE 5 Pin M12 Power Female 90C angle Connector+ 1.5Meter CABLE
ECABM12X83MSTP 8 Pin M12 X-coded RJ45 Male 3 METER, STP CABLE w/ Shielding
ECONM12-5P(M)-W-160 M12 5P(Male) 160 Degree Wire Type Connector (DI/DO)
USB adapter M12 to USB 2.0 interface adapter
ECAB124030MJS 4 Pin M12 RJ45 Male 3 Meters; STP Cable