Lantech TPGS-L5216MGT-10(16) is a high performance OS3 (All Gigabit) Ethernet switch with 16 10/100/1000T + 2 1G/2.5G Copper w/10(16) PoE 802.3af/at Ports which provides advanced security function for network aggregation deployment.
It delivers ITU G.8032 enhanced ring recovery less than 20ms in single ring. The QoS, advanced security including INGRESS/EGRESS* ACL L2/L3,TACACS+, SSH/SSL and subnet VLAN, protocol VLAN and Mac based DHCP server, DHCP Option 82, DHCP server,IGMPv1/v2/v3/router port are supported and also required in large network. It also supports10K Jumbo frames.
Up to 10/16 PoE at/af ports w/advanced PoE management
Compliant with 802.3af/at standard, the Lantech TPGS-L5216MGT-10(16) is able to feed each PoE port up to 30 Watt. Lantech TPGS-L5216MGT-10(16) supports advanced PoE management including PoE detection and scheduling. PoE detection can detect if the connected PD hangs then restart the PD; PoE scheduling is to allow pre-set power feeding schedule upon routine time table. Each PoE port can be Enabled/disabled, get the voltage, current, Watt, and temperature info displayed on WebUI.
Support PXE to verify switch firmware with the latest or certain version
The switch can check its firmware version during booting time via PXE protocol. If switch finds any newer version, it will upload automatically.
Miss-wiring avoidance, Node failure protection, Loop protection
The TPGS-L5216MGT-10(16) is also embedded with several features for stronger and reliable network protection in an easy and intuitive way. When the pre-set ring configuration failed or looped by miss-wiring, Lantech TPGS-L5216MGT-10(16) is able to send alert with the LED indicator and disable ring automatically.
Node failure protection ensures the switches in a ring to survive after power breakout is back. The status can be shown in NMS when each switch is back. This feature prevents the broken ring and keep ring alive without any re-configuration needed.
Loop protection is also available to prevent the generation of broadcast storm when a dumb switch is inserted in a closed loop connection.
DHCP option 82 & Port based, Mac based DHCP, Option66, IPv6 DHCP server
DHCP server can assign dedicated IP address by MAC or by port (Port based for single switch) , it also can assign IP address by port for multiple switches with single DHCP option82 server. DHCP Option66 server can offer IP address of TFTP server to DHCP client for VOIP application. IPv6 address resolution for basic DHCP service can be supported.
User friendly GUI, Auto topology drawing
The user friendly UI, innovative auto topology drawing and topology demo makes TPGS-L5216MGT-10(16) much easier to get hands-on. The complete CLI enables professional engineer to configure setting by command line.
Protocol based VLAN; Subnet based VLAN
The protocol-based VLAN processes traffic based on protocol. It filters IP traffic from nearby end-stations using a particular protocol such as IP, IPX, ARP or other Ethernet-types in a Hex value. Subnet based VLANs group traffics into logical VLANs based on the source IP address and IP subnet. The above features can help to build VLAN in the network mixed with managed and un-managed switch as to define packets to which VLAN group based on protocol or subnet based.
Enhanced G.8032 ring, 8 MSTI MSTP; MRP ring
Lantech TPGS-L5216MGT-10(16) features enhanced G.8032 ring which can be self-healed in less than 20ms for single ring topology protection covering multicast packets. It also supports various ring topologies that covers enhanced ring and basic ring by easy setup than others. It supports MSTP that allows RSTP over VLAN for redundant links with 8 MSTI.
MRP (Media Redundancy Protocol) can be supported for industrial automation networks.
IGMPv3, GMRP, router port, MLD Snooping, static multicast forwarding and multicast Ring protection
The unique multicast protection under enhanced G.8032 ring can offer immediate self-recovery instead of waiting for IGMP table timeout. It also supports IGMPv3, GMRP, router port, MLD snooping and static multicast forwarding binding by ports for video surveillance application.
Editable configuration file; USB port for upload/download the configuration
The configuration file of Lantech TPGS-L5216MGT-10(16) can be exported and edited with word processor for the following switches to configure with ease. The factory reset button can restore the setting back to factory default and built-in watchdog design can automatically reboot the switch when CPU is found dead.
The USB port can upload/download the configuration from/to USB dongle.
Event log & message; 2 DI + 2DO
In case of event, the TPGS-L5216MGT-10(16) is able to send an email** & SMS** text message to pre-defined addresses as well as SNMP Traps out immediately. It provides 2DI and 2DO. When disconnection of the specific port was detected; DO will activate the signal LED to alarm. DI can integrate the sensors for events and DO will trigger the outside alarm and switch will send alert information to IP network with email and traps.
Environmental monitoring for switch inside information
The environmental monitoring can detect switch overall temperature, total power load, actual input voltage and current. It also can send the SNMP traps, email** and SMS** alert when abnormal.
Up to @30W PoE+ output with 10/16 PoE ports; Dual WV isolated input with max PoE budget
The TPGS-L5216MGT-10(16) supports IEEE802.3at/af standard which can feed HI-power up to 30W at each PoE port for various IP PD devices. WVI model accept 16.8~137.5VDC dual isolated input with galvanic protection and can feed 54V output for PoE feeding with 80W budget.
Smart bypass protection on dual 1G/2.5G copper ports**
The bypass relay is set to bypass the switch to the next one when power is off to prevent network disruption. Lantech bypass caters to remain in bypass mode until the switch is completely booting up when power is back to avoid another network lost. Smart bypass can be activated when switch encounters power failure or watch dog hang.
EN50155, EN45545-2, EN61373 verification; High ESD protection
TPGS-L5216MGT-10(16) passed tests under extensive Industrial EMI and Safety standards. With EN45545-2 Fire & Smoke, EN50155 verification, the TPGS-L5216MGT-10(16) is best switch for railway on-board/track side, vehicle and mining applications. For more usage flexibilities, TPGS-L5216MGT-10(16) supports wide operating temperature from -40°C to 75°C.
|8361-470||TPGS-L5216MGT-10-54-WVI||16 10/100/1000T + 2 1G/2.5G Copper M12 X-coded w/10 PoE at/af EN50155 OS3 PoE Managed Ethernet Switch; 16.8V~137.5VDC dual isolated input; PoE budget 80W; IP54 housing; -40°C to 75°C|
|8361-4701||TPGS-L5216MGT-16-54-WVI||16 10/100/1000T + 2 1G/2.5G Copper M12 X-coded w/16 PoE at/af EN50155 OS3 PoE Managed Ethernet Switch; 16.8V~137.5VDC dual isolated input; PoE budget 80W; IP54 housing; -40°C to 75°C|
|9000-114||OS3 - L3L||OS3 software platform with Layer 3 Lite functions (please check Lantech software data sheet for details)|
|9000-115||OS3 – IEC61375-2-5||OS3 software platform with IEC-61375-2-5 ETBN (Ethernet Train Backbone Networks) function (please check Lantech software data sheet for details)|
|9000-116||OS3 – L3||OS3 software platform with Layer 3 functions (please check Lantech software data sheet for details)|
|ECON120005PF||M12 5P(Female) A-coded 160 Degree Crimp Type Connector|
|ECONM12-5P(F)1.5M CABLE||5 Pin M12 Power Female 90C angle Connector+ 1.5Meter CABLE|
|ECABM12X83MSTP||8 Pin M12 X-coded RJ45 Male 3 METER, STP CABLE w/ Shielding|
|ECONM12-5P(M)-W-160||M12 5P(Male) 160 Degree Wire Type Connector (DI/DO)|
|ECAB124030MJS||4 Pin M12 RJ45 Male 3 Meters; STP Cable|
|USB adapter (8850-102)||8 pin M12 (Male) A-coded 180 degree M12 to USB 2.0 interface adapter, 8cm|
|USB adapter set (8850-103)||8 pin M12 (Male) A-coded 180 degree M12 to USB 2.0 to DB9 (Female) Cable, 150cm + USB NIC|